Showing results: 91 - 105 of 383 items found.
-
Renesas Electronics Corp.
IGBT product series for Power Factor Correction (PFC), UPS, solar power generation, and welding applications, recommended for 50 to 100 kHz frequencies, and not guaranteed against short circuit.
-
Model TFT780 -
Gopal Electronics
Three Phase Power Analyzer PA700TFT is multi-range power Analyzer with basic 0.05% R+R accuracy. 8 range of voltage, 8 range of current and total 64 range of power and power factor gives more accurate result at low power factor. It has waveform mode to check the waveform of voltage and current. As well it has B/H curve mode where user can check live b/h curve of the transformer under test. The gap less four-quadrant power measurement technique gives better accuracy at distorted waveforms or AC drive (VFD) operated power supply.
-
Veer Electronics
Power Parameter MeasurementVoltage (V), Current (I), Power (P), Power Factor (PF), Apparent Power (VA), Reactive Power (VAR), Frequency (F) etc. Physical Parameter MeasurementTorque (Kgm), Output Power (Po), Efficiency of Motor, RPM, CRPM, % Slip etc.
-
GT Series -
Clary Corporation
The Global Uninterruptible Power System or GT Series, features Clary's On-Line Double Conversion technology, and is Power Factor Corrected for a wide range of voltage inputs, (120Vac through 240Vac and 50/60Hz).
-
MPM-1010/1010B -
Matrix Technology Inc.
MPM series intelligent electrical parameter measuring instrument is a set voltage test, current test, power test. Multi-functional measuring instrument with integrated power factor and high-speed processor inside.
-
Qualstik -
SensorLink
The Qualstik Power Quality Meter has been developed specifically for measurement of four important items of power quality in the electric utility industry. These are Current, True Power Factor, Total Harmonic Distortion and the Direction of Current Flow.
-
Shenzhen Graigar Technology Co.,Ltd.
This power analyzer is used for single-phase or three-phase measurements of the active, reactive and apparent power, power factor, phase angle, energy, voltage, current as well as peaks and harmonics up to 50º of the harmonic waveform. The power analyser clamp is equipped with data logger.
-
-
NV CONFIGURABLE Series -
TDK-Lambda Corp.
*1-5 Outputs*Up to 90% Efficient*Active Power Factor Correction*Universal Input (90 - 264VAC)*No Minimum Loads*Medical Approvals
-
STMicroelectronics
With robust, advanced high-voltage converters, power factor correctors, a variety of controllers and supervisors/housekeeping ICs, together with innovative architectures and extended temperature ranges. New generation AC-DC converters reduce power consumption and increase efficiency, essential for powering the majority of mains equipment. When combined together, ST power factor correctors, PWM controllers and offline converters significantly lower system power consumption to outperform the most demanding energy-saving regulations, such as 80 PLUS® Initiative, ErP Lot 6, Energy Star, and many others.
-
RCD -
Junxy Energy
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
W-IE-NE-R, Plein & Baus GmbH
The WIENER MTCA.4 is a low noise and ripple / high power density power supply in a double height / double width form factor. Designed according to the PICMIC MTCA-4 standard it provides 1000W for 12V payload power as well as 3.3V management power.
-
ZWS-BAF Series -
TDK-Lambda Corp.
*Universal input (85 - 265VAC)*10 Year e-cap Lifetime*Power Factor Corrected*Convection Cooled*Compact Design*Five year warranty
-
K-1000 Resistive & Inductive -
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
D Series -
PRODIGIT Electronics Co, Ltd.
The programmable DC power supply is equipped with active power factor correction to improve circuit efficiency. The full range input voltage makes it suitable for most industries and countries without requiring a voltage conversion switch.